Electronic Automatic Temperature Control ( EATC ) Retrofit

Note

this guide is still in the making at the minute so is not a full guide just yet but more info will be added when i get a minute.

Required Parts

EATC Control Unit Interior Temperature Sensor EATC Fan Motor Sunload Sensor New Dashtop Airvent Grill to accept the new Sunload sensor ( your old grill can be suitably modified if your handy with a drill )

Wiring ( preferably removed from a complete ghia/ghia x dashboard loom but if not then a selection of ends with some wiring will do but will require lots of joins to be made instead of just 1 like a complete loom will require )

if your going the plugs only route you will need :-

EATC control unit plug with wires ( either plug as the pins inside are the same ( require 6 wires/connectors from inside it )

EATC fan motor plug with wires ( remove the connector @ pin 1 ready to accept the lead from pin 1 of your current motors connector ( leaves the other 3 wires in the plug nice & tidy & means a much easier job )

Interior Temperature Sensor connector plug to connect the temperature sensor to the EATC control unit

Sunload Sensor Plug to also connect this upto the EATC control unit

Lowest Green Fusebox Plug for one of its connections ( to power the interior temperature sensor )

if your going the full wiring loom route your will require :-

ghia/ghia x dash loom from which you will need the following :-

Fan motor wiring ( earth lead & 2 wires to the control unit - the 4th wire can simply be removed from the plug very easily )

Temperature & sunload sensor wiiring ( this is a the one that may take the longest to remove as 1 wire goes all the way to the fusebox & its also joined to a 3rd sensor which is already inplace on your car ( this 3rd sensor will need to be cut off ( one wire ) from the other sensors but make sure you leave enough wire to easily connect the wire from the car at the minute to it later )

( its also worth marking the wires locations as you remove them for easier refitting later ( make sure your cutting off the correct sensor wire too as the sunload & the sensor wiring your cutting off have the same kinda plug & the wiring colours are almost identical too, but the wiring is reversed at the plug ( this can easily be reversed if you do make a boo-boo though )

( insert piccy of kit required here )

Method

There are 3 levels of upgrade:

Option 1

Getting The Look but not the full function.

The manual knobs can be directly replaced for the digital unit no wiring changes required, this gives you a quick "sexy looking dash" - the digital unit will work for temp control, air direction, aircon on/off and recirc. However, the fan speed has to be set using the manual knob and this knob left behind the dash after reassembly.

Option 2

Installing an auto fan too.

This has four connections running to it. Green / Red (or) Brown power this already exists in manual aircon cars it can be used to power the auto fan. Black (earth) -just earth this to a suitable point under the dash. Brown/Blue connection which goes to the No 1 connection on Black socket on the back of the Digital Control unit. Blue / White connection which goes to No3 connection of the same socket.

(On Manual Aircon cars, Connection No1 will have a black / white running to it just cut this off and connect the brown / blue wire).

You can leave the manual fan speed switch behind the dash as it is redundant now.

Both the white and black harness sockets for the control unit can be easily taken apart by sliding the end cap off an then removing the plug with cables, you need a bionic eye here but the holes have been numbered in each corner.

When this modifcation is completed you should have a fully working (manual) digital control unit - all functions except the Auto.

Option 3

The Full Retrofit.

There are 2 additional sensors, the sunload sensor which fits into the screen demister vent. This vent will need to be removed as you need to drill a hole (same diameter as the sun load sensor - about 12mm) in the circular blank.

The most awkward part I found was running the sunload sensor cables (2 of them) through to the control unit. In the end I removed the speedo housing and drilled a 5mm hole into the demister vent under the dash and fed the cables through - BE CAREFUL HERE NOT TO DRILL INTO AND THROUGH THE TOP TRIM OF YOUR DASH.

The interior motorised sensor will clip into a recess under the drivers trim to the left of the steering wheel - you will see a slotted vent about the size of a 10 pence piece.

Once this has been done you can re-assemble everything as I was able to work with just the radio removed.

The motorised sensor has four cables one of which is power that is fed to the fuse box.

( insert wiring connection points here & also more piccies )

Things To be Aware of & checks to make

Mine is still all working well - the temp inside the car is being maintained and as a quick check once all the wiring is complete if you turn the temp up full the fan will slowly speed up and then once the desired temp is achieved will slow down. (there is a slight delay - say 10 seconds). Once you have the auto working and select it none of the indicator lights on the EATC control unit will light up (not even the Aircon one) as the unit is doing it all automatically) - your aircon will kick in and out automatically. Obviously all this can be manually overridden by selecting your own settings (the indicator lights will then illuminate your desired settings).

Another check is when you select screen the auto fan should come in on high (aircon on although the light will not come on)and all air directed to the screen.

How-to taken from forum user Taffiboy

Some minor additions by Compuwiz_uk