Registrations

We now manually approve all new user accounts due to a large influx of spam bots. Accounts are normally approved within 48 hours.

If you need any help with using this Wiki, please ask here: TalkFord.com Wiki Submission Forum

F Super

From www.FordWiki.co.uk
Revision as of 17:17, 12 April 2013 by Peter scott (Talk | contribs)

Jump to: navigation, search

Fordwiki infobox.png
Overview Guide
Ford Model: Mondeo_Mk3
Petrol/Diesel: Diesel
Estimated Cost: ?
Difficulty? Easy/Medium
How long does this take? ?

The F-Super / Formidable Instruction Manual

File:F Super Formidable Manual.pdf


A frequently asked question is "Can F-Super re-code my injectors?"

The answer depends on the build date of your car.

Cars with with automatic transmission and build date 15/06/2003 and later (i.e. 3Y) and cars with manual transmission and build date 15/02/2003 and later (i.e. 3K) can have their injector codes written to and read from the PCM by F-Super but earlier cars cannot.

For the Transit the build date is 07/2003 and later (i.e. 3S).

To determine your car's build date check the characters 11 and 12 on your VIN number.

The Transit has a longer VIN code but the year and month codes are still 11 and 12 characters to the right of the W.

Build Date 2.jpg


Identifying and Coding Injectors

Notes:

1.The engine should be stone cold prior to re-coding. At least 8 hours since last run.

2. The action of writing the codes into the ECU also resets the fuel trim values that the ECU adjusts by listening to the knock sensor mounted on the cylinder block. Each injection normally consists of a small pilot injection followed by the main injection. Immediately after recoding, the pilot injection will be reset to zero. This will cause the engine to sound more like an old taxi for a while until the ECU readjusts the pilot injections. This readjustment may take quite a substantial time to return to normal.

Injector Leakage

Injectors can leak in two different ways. The Leak-Off Test above is measuring the leakage through the valve. Excessive leakage makes it impossible for the injection pump to achieve or maintain the pressure in the common rail that the ECU demands. When this happens the ECU will restrict performance or shut the engine down and record a DTC error such as P1211 indicating a failure to achieve correct pressure.

The other form of leakage is past the needle. In this case the fuel leaks into the cylinder when it shouldn't. The effect of this leakage is to cause firing too early or of greater magnitude than desired. The ECU will detect this when the knock sensor shows excessive knock. When this happens the engine will be put into limp mode and one or more of the following DTCs will be recorded.

P2336 Cylinder #1 Above Knock Threshold

P2337 Cylinder #2 Above Knock Threshold

P2338 Cylinder #3 Above Knock Threshold

P2339 Cylinder #4 Above Knock Threshold

If leakage of either type is caused by wear then the only cure is the replacement of the complete injector, however it is possible that leakage can be caused by carbon build-up at in the tip or by contamination by other forms of dirt, in this case it may be possible to repair the injector by cleaning. See: [TDCi Injector Cleaning] https://www.fordwiki.co.uk/index.php?title=Injector_Cleaning


Fsuper1.jpg


MAP, BARO and Boost Pressure

F Super is very good but the Live Data screen has some problems with the stated units:

MAP has units of kPA but the actual values shown in the F Super window need to be multiplied by 10 to be correct. (e.g. At rest the MAP should just read atmospheric pressure which is about 100 kPa but F Super reads 10 kPa)

Likewise the BARO reading in F Super should normally read about 1000 mb (millibars) but actually displays about 100 mb.

So, if you wanted to know what your Boost Pressure was:

Boost pressure in psi = ((10xMAP) - BARO) / 6.895

e.g. If the MAP is reading 23 in F Super and BARO is reading 100 we can say that the boost pressure is:

230 - 100 = 130 kPa. i.e. 18.85 psi

1 bar = 100 kPa.

1 psi = 6.895 kPa.

Accelerator Pedal Position Sensors APP1, APP2, APP3

See: http://articles.d-tips.com/art8.html