Registrations

We now manually approve all new user accounts due to a large influx of spam bots. Accounts are normally approved within 48 hours.

If you need any help with using this Wiki, please ask here: TalkFord.com Wiki Submission Forum

Instrument Cluster Self-Diagnostic Mode

From www.FordWiki.co.uk
Revision as of 03:50, 7 April 2009 by 52graphite (Talk | contribs)

Jump to: navigation, search

Applicability

This is for the MK3 Mondeo but will also work on the Focus (Mk1 and Mk2) and most other Ford vehicles with a digital trip meter.

Entering Self-Diagnostic Mode

To enter the instrument cluster Self-Diagnostic Mode simultaneously press and hold the tripmeter reset button and turn the ignition switch to position II.

When tESt is displayed in the LCD release the button.

The instrument cluster will enter the gauge sweep test.

To navigate through the Self-Diagnostic Mode tests press the tripmeter RESET button repeatedly as required.

The self-test is deactivated when the ignition switch is turned to the OFF position or when the tripmeter reset button is pressed and held for 5 seconds.

Available information

Your car may differ from these slightly in content and sequence:

  • Gauge test
  • All LCD are illuminated
  • Indicator bulbs
  • ROM level (r----)
  • NVM (EEPROM) level (Er----)
  • DTC revision level (dtC985)
  • DTC. The DTCs stored will be displayed. The DTC codes will scroll through if there is more than one, or "nOnE" if there are none. See below for interpretation.
  • Road speed mph (SP----)
  • Road speed km/h (SP----)
  • Averaged speed, some sort of hex reading (S60---)
  • Engine speed rpm (TA----)
  • Averaged tacho signal, some sort of hex reading (T60---)
  • Odometer counter (od ---)
  • Fuel level sensor (F ---, 010 (empty) - 254 (full))
  • Averaged fuel level (F60---, range as above)
  • Fuel flow rate (FL --, hex counter)
  • Fuel percentage/remaining? Hex? (FP --)
  • Cylinder head temperature (---C)
  • Battery voltage (bAt---)

There are many other pieces of information not of interest to the end user, but you'll eventually get back round to the gauge sweep.

Cluster DTCs

To read the complete list of codes, you'll need a dedicated fault code reader plugged into the diagnostic port. Some codes are available via the cluster, listed under the DTC entry described above. These are:

  • 115A (P115A) Low Fuel Level - Forced Limited Power
  • 115B (P115B) Low Fuel Level - Forced Engine Shutdown
  • 9202 (B1202) Fuel pump and sender unit/fuel level sensor open circuit
  • 9204 (B1204) Fuel pump and sender unit/fuel level sensor short to ground
  • 9317 (B1317) Battery voltage high (greater than 16V)
  • 9318 (B1318) Battery voltage low (less than 10V)
  • 9342 (B1342) PCM is defective
  • 9342 (B1342) Odometer RESET button sticking
  • 9342 (B1342) Trip computer SET button sticking
  • 9342 (B1342) NVM memory failure
  • A286 (B2286) MODE switch sticking
  • 9359 (B1359) Ignition run/accessory circuit failure
  • A477 (B2477) Module configuration failure
  • D262 (U1262) Communication bus fault (missing CAN messages)
  • E196 (U2196) Invalid data for engine RPM (Invalid CAN message)
  • E197 (U2197) Invalid data for vehicle speed (Invalid CAN message)
  • E198 (U2198) Invalid data for fuel pulse (Invalid CAN message)
  • E199 (U2199) Invalid data for engine coolant temperature (Invalid CAN message)
  • E200 (U2200) Invalid data for odometer (Invalid CAN message)
  • E201 (U2201) Invalid data for ambient temperature (Invalid CAN message)