Registrations

We now manually approve all new user accounts due to a large influx of spam bots. Accounts are normally approved within 48 hours.

If you need any help with using this Wiki, please ask here: TalkFord.com Wiki Submission Forum

Difference between revisions of "Rear washer jet replacement"

From www.FordWiki.co.uk
Jump to: navigation, search
m
Line 14: Line 14:
 
|header1 =  
 
|header1 =  
 
|label1  = Ford Model:
 
|label1  = Ford Model:
|data1  = '''Mondeo'''
+
|data1  = '''Mondeo Mk3 hatch'''
 
|header2 =  
 
|header2 =  
 
|label2  = Petrol/Diesel:
 
|label2  = Petrol/Diesel:
|data2  = '''????'''
+
|data2  = '''all'''
 
|header3 =  
 
|header3 =  
 
|label3  = Estimated Cost:
 
|label3  = Estimated Cost:
|data3  = '''????'''
+
|data3  = '''a few quid'''
 
|header4 =  
 
|header4 =  
 
|label4  = Difficulty?
 
|label4  = Difficulty?
|data4  = '''????'''
+
|data4  = '''Easy'''
 
|label5  = How long does this take?
 
|label5  = How long does this take?
|data5  = '''????'''
+
|data5  = '''15 mins'''
 
}}
 
}}
  

Revision as of 09:35, 8 March 2011

The Ford Mondeo hit our roads in 1993, and has consistently been a sales success. Now on its 4th incarnation, it remains a drivers favourite.
For more information, visit the Ford Mondeo forum on TalkFord.com, the definitive resource site covering all Fords from the present day to the 1970's.

Fordwiki infobox.png
Overview Guide
Ford Model: Mondeo Mk3 hatch
Petrol/Diesel: all
Estimated Cost: a few quid
Difficulty? Easy
How long does this take? 15 mins

This is for the hatchback only.

If your rear washer jet isn't performing well and you're sure the "usual suspect" pipe join behind the RH C-pillar trim is secure, here's how to replace your rear washer jet. This is a quick and easy process that should take about 10 minutes tops, assuming you don't waste time taking photos for the Wiki as you go.

Buy the part

FINIS code 1144075, cost me £3.58. This includes the rubber gasket / washer.

Here's the packet:

Nrw-packet.jpg

and the new part:

Nrw-part.jpg

Remove the old part

Twist the old washer jet 45 degrees towards the RH side of the car. Why do I always take Wiki pictures after dusty rain?!

Nrw-twist.jpg

Remove the two screws holding the centre brake light cover on, and drop the cover. The lamp and wiring stay attached, so be gentle.

Nrw-cover.jpg

Using a screwdriver, push the arrowed tab on the old washer jet to persuade it through the hole. This shouldn't take much force.

Nrw-tab.jpg

From outside the car, pull the jet out a couple of inches and disconnect the pipe.

Fit the new part

Plug the new part into the pipe. This photo came out unexpectedly artistic:

Nrw-fitted.jpg

Clean up the paintwork where the washer sits. Locate the front-facing tab of the new washer jet into the hole - straight, not twisted - and push down to locate the rear tab. Give the new jet a quick test to make sure the pipe isn't kinked, then refit the lamp cover making sure not to trap the wiring. Ensure the brake light still works.

Job done.